1 106 просмотров
Рейтинг статьи
1 звезда2 звезды3 звезды4 звезды5 звезд
Загрузка...

Status sec dl forbidden 0xc0020004 как исправить

[Please help] HELP PLZ.. MEIZU M5 NOTE Dead After Format using SP Flash Tool.

****If I posted in a wrong section, please advise me. Im new here, link me to where this should be.. Thank youu

Please if Anyone can help. I badly badly need your help. . . Highest Appreciations.

It has been 2 long months since I bricked my Meizu M5 Note (M1621), and searched and worked on reviving it. It was running Flyme 7.0 Official, I rooted it. After months of realizing that there’s not much to do with a rooted phone and thought about its security, I decided to unroot using SuperSU, but it made it stuck in loading Flyme logo —- could not boot.

Mistake: I panic and never thought that it has an SD card Slot on sim port 2, so I formatted the Phone using SP flashtool 5.1632. After that, it no longer booted; no power ON, no charging, no recovery.

****The Phone can still be read by the SP Flash tool. DA Download 100% then fails. So now, I decided to contact Meizu official techs in the Philippines. They’re Meizu guardians here, but guess what. they said that the main board is dead. So I pulled the phone back. I think they did it on purpose: After a week, a buddy sent me a message on facebook, asking if I have a bricked Meizu m5 Note. You know what it seemed to be, right. ****

So, I tried now myself: Found four STOCK-ROMS:

– SW_K96092DA1_V007_HW_96092_1_20M21_M1621_USR_signed
– M1621 Flyme 5.2.11.1G (NO Change MB)
– 20161220032104_intl_prd_stable_fvcs_stable_5.2.11.0G
– 20161107170347_prd_stable_fvcs_stable

– Tried Flashing again using the same Version of SP Flash Tool Above, but its getting errors.

Version that were tried so far:

SP Flash tool ver. 5.1632
SP Flash tool ver. 5.1744
SP Flash tool ver. 5.1804
SP Flash tool ver. 5.1824
SP Flash tool ver. 5.1904
And SP Flash tool ver. 5.1452 (never worked)

In all of them, I get the same errors:

ERROR : STATUS_SEC_DL_FORBIDDEN (0xC0020004) – I’ve read in your respected page that I have to untick the Preloader.bin, but it gets 3 diff errors:

ERROR : STATUS_BROM_CMD_SEND_DA_FAIL (0xC0060003)

ERROR : STATUS_BROM_CMD_SEND_DA_FAIL (0xC0060005)

ERROR : STATUS_SEC_DL_FORBIDDEN (0xC0020004)

– I’ve also read that the Preloader must be flashed first; tried all those versions above but it gives the forbidden error 20004 still.

– Disassembled the phone, dettached the battery, and flash. Still no good. Same errors.

– Press Volume +, Volume -, or Both before or while plugging the usb to get to META mode, but it got the same error.

Other tools that were tried:

Читать еще:  Чем объяснить разнообразие взглядов на прогресс

Miracle Box Cracke 2.58 + loader – Downloaded here as well. This tool looked so promising, it read the phone but upon flashing, it crashes. Tried a few times but scared to burn the Main Board.

Miracle thunder 2.82 + loader – It reads the phone, gives the sign that the DA is being downloaded. Stuck in 100%, nothing there after..

If anyone has a probing questions, suggested tools and or an Idea on how I can flash the firmware to resurrect my Meizu M5 Note again, it would be so appreciated, and praised. .. The phone is still alive, I know! . but currently in coma .

Thanks in Advanced.

****If I posted in a wrong section, please advise me. Im new here, link me to where this should be.. Thank youu

Thanks to sicariusM5

(03-24-2019, 08:29 AM) sicariusM5 Wrote: ****If I posted in a wrong section, please advise me. Im new here, link me to where this should be.. Thank youu

Please if Anyone can help. I badly badly need your help. . . Highest Appreciations.

It has been 2 long months since I bricked my Meizu M5 Note (M1621), and searched and worked on reviving it. It was running Flyme 7.0 Official, I rooted it. After months of realizing that there’s not much to do with a rooted phone and thought about its security, I decided to unroot using SuperSU, but it made it stuck in loading Flyme logo —- could not boot.

Mistake: I panic and never thought that it has an SD card Slot on sim port 2, so I formatted the Phone using SP flashtool 5.1632. After that, it no longer booted; no power ON, no charging, no recovery.

****The Phone can still be read by the SP Flash tool. DA Download 100% then fails. So now, I decided to contact Meizu official techs in the Philippines. They’re Meizu guardians here, but guess what. they said that the main board is dead. So I pulled the phone back. I think they did it on purpose: After a week, a buddy sent me a message on facebook, asking if I have a bricked Meizu m5 Note. You know what it seemed to be, right. ****

So, I tried now myself: Found four STOCK-ROMS:

– SW_K96092DA1_V007_HW_96092_1_20M21_M1621_USR_signed
– M1621 Flyme 5.2.11.1G (NO Change MB)
– 20161220032104_intl_prd_stable_fvcs_stable_5.2.11.0G
– 20161107170347_prd_stable_fvcs_stable

– Tried Flashing again using the same Version of SP Flash Tool Above, but its getting errors.

Version that were tried so far:

SP Flash tool ver. 5.1632
SP Flash tool ver. 5.1744
SP Flash tool ver. 5.1804
SP Flash tool ver. 5.1824
SP Flash tool ver. 5.1904
And SP Flash tool ver. 5.1452 (never worked)

Читать еще:  Чем кормить раков в домашних условиях

In all of them, I get the same errors:

ERROR : STATUS_SEC_DL_FORBIDDEN (0xC0020004) – I’ve read in your respected page that I have to untick the Preloader.bin, but it gets 3 diff errors:

ERROR : STATUS_BROM_CMD_SEND_DA_FAIL (0xC0060003)

ERROR : STATUS_BROM_CMD_SEND_DA_FAIL (0xC0060005)

ERROR : STATUS_SEC_DL_FORBIDDEN (0xC0020004)

– I’ve also read that the Preloader must be flashed first; tried all those versions above but it gives the forbidden error 20004 still.

– Disassembled the phone, dettached the battery, and flash. Still no good. Same errors.

– Press Volume +, Volume -, or Both before or while plugging the usb to get to META mode, but it got the same error.

Other tools that were tried:

Miracle Box Cracke 2.58 + loader – Downloaded here as well. This tool looked so promising, it read the phone but upon flashing, it crashes. Tried a few times but scared to burn the Main Board.

Miracle thunder 2.82 + loader – It reads the phone, gives the sign that the DA is being downloaded. Stuck in 100%, nothing there after..

If anyone has a questions, and an Idea on how I can flash the firmware to resurrect my Meizu M5 Note again, it would be so appreciated, and praised. The phone is still alive, I know! . but currently in coma .

Тема: Meizu u20 кирпич после формата FlashTool

Опции темы
Отображение
  • Линейный вид
  • Комбинированный вид
  • Древовидный вид

Meizu u20 кирпич после формата FlashTool

Wait for phone.
Phone found! [ 54 ]
Sync.
Inital Boot Ok!
BB_CPU_PID : 6755
BB_CPU_NME : [MediaTek] Helio[P10]|MT6755_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x07000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : LOCKED with SLA
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA .

[DA_ERROR] : SECURITYBOOT_BOOT_NOT_ACCEPTED
Boot Error!

Operation Failed
Elapsed: 00:00:08
Reconnect Power/Cable!

Флештул в любых “позах” пишет всякие secure ошибки.

Способ восстановления кирпичей отформатированных флештулом .

1. Качаем сервисную прошивку
, флештул модифицированный (пароль 777) , отключаем антивирусы .
2. Установить драйвер
3. Запустить флаштул, в папке flash_tool запускаем 魅族MTK专用.exe (использовать только этот флаштул)
4. В поле Download Agent – MTK_AllInOne_DA
5. В поле Authentication File – auth_sv5 из папки флаштул
6. В поле Scatter-loading File – MT6755_Android_scatter.
порядок такой 1й-Download Agen 2й-Authentication File 3й-Scatter-loading File
7. Режим загрузки рекомендуется Download Only
8. Во флаштуле нажимаем на кнопку Download и подключаем отключенный телефон к ПК

Следующие 3 пользователей поблагодарили Бахтияр.uz за это сообщение:

тоже такой же трупик принесли после формата, как его поднять без флеш тула через см2? может есть у кого файл бута?
Переодически запускаю мод флеш, но он пока не арбайтен, и вообще он когда нибудь работал? вторые сутки пошли, трупик пока трупик, скачал кучу бутов под см2, но и тут тоже не выходит ни чего, кроме сквернословия.

Читать еще:  Какие требования предъявляются к командированному персоналу

Способ восстановления кирпичей отформатированных флештулом .

1. Качаем сервисную прошивку
, флештул модифицированный (пароль 777) , отключаем антивирусы .
2. Установить драйвер
3. Запустить флаштул, в папке flash_tool запускаем 魅族MTK专用.exe (использовать только этот флаштул)
4. В поле Download Agent – MTK_AllInOne_DA
5. В поле Authentication File – auth_sv5 из папки флаштул
6. В поле Scatter-loading File – MT6755_Android_scatter.
порядок такой 1й-Download Agen 2й-Authentication File 3й-Scatter-loading File
7. Режим загрузки рекомендуется Download Only
8. Во флаштуле нажимаем на кнопку Download и подключаем отключенный телефон к ПК

Status sec dl forbidden 0xc0020004 как исправить


Welcome to the GSM-Forum forums.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features.
Only registered members may post questions, contact other members or search our database of over 8 million posts.

Registration is fast, simple and absolutely free so please – Click to REGISTER!

If you have any problems with the registration process or your account login, please contact contact us .

PRELOADER :
EMI : DEV : MT6755
EMI : SRC : preloader_m1611.bin
EMI : CNT : 0008
EMI : [00] : eMCP : eMMC+LP/DDR3 , ID : 150100513832334D42 : VEN : SAMSUNG | DEV : Q823MB : RAM : [ 2.00 GB ]
EMI : [01] : eMCP : eMMC+LP/DDR3 , ID : 90014A484147326505 : VEN : HYNIX | DEV : HAG2e : RAM : [ 2.00 GB ]
EMI : [02] : eMCP : eMMC+LP/DDR3 , ID : 700100454841434541 : VEN : KINGSTON | DEV : EHACEA : RAM : [ 2.00 GB ]
EMI : [03] : eMCP : eMMC+LP/DDR3 , ID : 90014A484247346132 : VEN : HYNIX | DEV : HBG4a2 : RAM : [ 3.00 GB ]
EMI : [04] : eMCP : eMMC+LP/DDR3 , ID : 150100525831424D42 : VEN : SAMSUNG | DEV : RX1BMB : RAM : [ 3.00 GB ]
EMI : [05] : eMCP : eMMC+LP/DDR3 , ID : 150100523231424D42 : VEN : SAMSUNG | DEV : R21BMB : RAM : [ 3.00 GB ]
EMI : [06] : eMCP : eMMC+LP/DDR3 , ID : 150100514531334D42 : VEN : SAMSUNG | DEV : QE13MB : RAM : [ 2.00 GB ]
EMI : [07] : eMCP : eMMC+LP/DDR3 , ID : 13014E51334A393756 : VEN : MICRON | DEV : Q3J97V : RAM : [ 3.00 GB ]

MOBILE :
RAM : NONE: 0x00040000 [ 256.00 KB ]
RAM : NONE: 0xC0000000 [ 3.00 GB ]
EMMC: 150100525831424D420761C468A314D1
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : RX1BMB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
GP1 : 0x00000000 [ 0 B ]
GP2 : 0x00000000 [ 0 B ]
GP3 : 0x00000000 [ 0 B ]
GP4 : 0x00000000 [ 0 B ]
USER : 0x747C00000 [ 29.12 GB ]

PRELOADER init FAILED!
ERR : 0xC0020004
ERR : SEC_DL_FORBIDDEN
ERR : 0x00000000|0x0002D824

Error : Failed to write data! Connection ( or secured region. ) problem!
Seems as some of MANDATORY section of FW is damaged! If device alive and work – send report!

Источники:

http://forum.hovatek.com/thread-27125.html
http://www.gsmforum.ru/threads/290077-290077?p=1303375
http://forum.gsmhosting.com/vbb/f296/preloader-init-failed-err-0xc0020004-meizu-m5-m1611-2547694/

0 0 голоса
Рейтинг статьи
Ссылка на основную публикацию
Статьи c упоминанием слов: